ABS

7 min read ยท Updated

HEPA vs. ULPA Filters

HEPA and ULPA filters both remove airborne particles from cleanroom and critical-space air supplies, but they are not interchangeable. The difference comes down to the particle size each is tested against, the efficiency required at that size, and the pressure-drop and cost tradeoffs that follow from using denser filter media. Specifying the wrong grade either wastes energy and budget or fails to achieve the required cleanliness.

๐Ÿ“ Educational scope

This guide explains HEPA and ULPA filtration for educational purposes. Filter selection for a specific cleanroom or critical space should follow the mechanical engineer's design and the applicable project specification.

The Core Difference: Particle Size and Efficiency

Both HEPA and ULPA are efficiency classifications, not brand names or a single fixed product โ€” they describe how well a filter captures particles at a defined "worst case" size, called the Most Penetrating Particle Size (MPPS). Filters are actually least effective at MPPS, not at the smallest particle size, because of how the three particle-capture mechanisms (interception, impaction, and diffusion) interact โ€” very small particles diffuse and are easily caught, very large particles are impacted and caught, but mid-range particles near MPPS slip through most easily.

Standard Test particle size Minimum efficiency
HEPA (US DOE/IEST) 0.3 ยตm 99.97%
HEPA H13 (EN 1822) MPPS 99.95%
HEPA H14 (EN 1822) MPPS 99.995%
ULPA (US DOE/IEST) 0.12 ยตm 99.999%
ULPA U15โ€“U17 (EN 1822) MPPS 99.9995%โ€“99.999995%

Two things stand out: ULPA is tested against a smaller target particle (0.12 ยตm vs. 0.3 ยตm), which is inherently harder to capture, and it is required to catch a larger fraction of those particles. Both factors compound โ€” a filter that is ULPA-rated is meaningfully more restrictive to airflow than one that is HEPA-rated, even before accounting for real-world loading.

Why Higher Efficiency Has a Cost

Filter media achieves higher efficiency primarily by being denser โ€” finer fibers, packed more tightly. Denser media resists airflow more, which shows up as higher pressure drop across the filter. Since a fan pushing air through a system experiences resistance from every component in series, a denser final filter raises total system static pressure, which the fan laws show has real consequences:

This is why ULPA is specified only where its added performance is actually required by the process โ€” not adopted by default on the assumption that "more efficient is always better."

When Each Is Required

Filter grade is one input to achieving a target ISO cleanliness class, not the whole answer โ€” air change rate, airflow pattern, room leakage, and personnel/process particle generation all matter too. As a general pattern:

Mixing the two within one facility is common: a semiconductor fab might run ULPA in its most critical lithography bays while the surrounding ISO 6โ€“7 support areas run HEPA, balancing performance against the fan energy and filter-replacement cost of running ULPA everywhere.

Testing and Certification

Both filter classes are scan-tested at the factory and again after installation. In-place leak testing follows ISO 14644-3: a challenge aerosol (typically PAO, which has largely replaced DOP for health and environmental reasons) is introduced upstream of the filter bank at a controlled concentration, and a calibrated photometer or particle counter scans the entire downstream filter face, frame, and gasket seal in overlapping passes. Any point where penetration exceeds the allowable threshold indicates a leak โ€” most commonly a gasket seal failure or a pinhole in the media โ€” and the filter or seal must be repaired or replaced before the room can be certified.

This is also where installed system performance can diverge from the filter's rated efficiency: a perfectly manufactured HEPA filter with a compromised gasket seal will leak far more than its media efficiency alone suggests. Certification testing verifies the installed condition, not just the filter's factory rating.

Common Mistakes

Specifying ULPA as a default "better safe than sorry" choice: This adds fan energy cost, filter cost, and replacement frequency without functional benefit if the target ISO class was already achievable with HEPA.

Assuming filter grade alone determines ISO class: A room with ULPA filters but poor airflow pattern, excess leakage, or high particle generation from personnel can still fail to achieve a clean classification. Filtration is one component of a system.

Confusing MERV-rated filters with HEPA/ULPA: MERV (Minimum Efficiency Reporting Value, used for general HVAC filtration per ASHRAE 52.2) tops out around MERV 16, which is roughly equivalent to a low-grade HEPA at best. MERV-rated filters are not a substitute for certified HEPA or ULPA filtration in a classified cleanroom.

Ignoring pressure drop in system design: Upgrading final filtration to ULPA after a system was designed around HEPA's pressure drop can overload the existing fan, reducing delivered CFM below design โ€” the exact opposite of the intended cleanliness improvement.

FAQ

What does HEPA stand for and what is its efficiency rating?+
HEPA stands for High-Efficiency Particulate Air. A HEPA filter must remove at least 99.97% of particles at 0.3 microns (ยตm) โ€” the Most Penetrating Particle Size (MPPS), where filtration is hardest โ€” under the US DOE/IEST standard. The European EN 1822 standard defines a range of HEPA grades (H13 and H14) with efficiencies from 99.95% up to 99.995%, tested at each filter's own individual MPPS rather than a fixed 0.3 ยตm.
What does ULPA stand for and how is it different from HEPA?+
ULPA stands for Ultra-Low Penetration Air. A ULPA filter must remove at least 99.999% of particles at 0.12 ยตm under the US standard โ€” both a smaller target particle size and a higher required efficiency than HEPA. Under EN 1822, ULPA corresponds to grades U15 through U17, reaching up to 99.999995% efficiency at the filter's MPPS. In practical terms, ULPA catches a higher fraction of smaller particles than HEPA.
Why not just always use ULPA if it is more efficient?+
Higher efficiency media is denser, which increases resistance to airflow โ€” pressure drop. Higher pressure drop means fans work harder to move the same CFM, increasing energy consumption and horsepower requirements per the fan laws. ULPA filters also cost more, load with particulate faster (shortening service life in dirty environments), and are unnecessary for cleanliness levels HEPA already satisfies. ULPA is reserved for applications where its added efficiency is functionally required, not used as a default upgrade.
Which cleanroom ISO classes require ULPA filtration?+
There is no single universal rule, since achievable classification depends on the whole system โ€” not filter grade alone โ€” but ULPA is typically reserved for ISO 3 and cleaner (and sometimes ISO 4) applications such as advanced semiconductor lithography, where HEPA's particle penetration at the smallest sizes is no longer sufficient. Most pharmaceutical aseptic filling (ISO 5) and general semiconductor manufacturing (ISO 4โ€“6) are achieved with HEPA filtration at sufficient air change rates and proper system design.
How are HEPA and ULPA filters tested and certified?+
Individual filters are factory-tested and scan-tested for leaks using a photometer or particle counter against a challenge aerosol (typically DOP or PAO โ€” poly-alpha-olefin, which has replaced DOP in most facilities for health reasons). After installation, TAB technicians perform an in-place leak test โ€” scanning the entire filter face and frame seal with a calibrated photometer while introducing challenge aerosol upstream โ€” to confirm no bypass leakage around gaskets or through pinholes, per ISO 14644-3 procedures.
Do ULPA filters need to be replaced more often than HEPA?+
Often yes, though it depends on the loading environment. Because ULPA media is denser and captures more of the finest particles, it can reach its terminal pressure drop (the point requiring replacement) faster than HEPA media under the same particulate load. Facilities using ULPA typically budget for more frequent filter change-outs and factor that cost into the decision to specify ULPA over HEPA in the first place.