ABS

Fan Sheave and Pulley Calculator

For belt-drive fans that are moving too much or too little air. Enter the motor speed, the two sheave sizes, and the measured and design airflow. The calculator returns the current fan RPM, the RPM needed to hit design, the sheave size that gets there, and what the change does to motor load.

⚠ Check the motor before changing fan speed

Horsepower rises with the cube of fan speed. Compare measured motor amps with nameplate full-load amps before and after any speed increase. Lock out and tag out the unit before touching belts or sheaves.

Fan Sheave Calculator

How a Sheave Change Fixes Airflow

On a belt-drive fan the motor turns at a fixed speed, and the ratio of the two sheaves sets how fast the fan turns. When a system's total airflow is off by more than the dampers should be asked to correct, the technician changes that ratio. Throttling a fan that is 20% high with dampers wastes energy and adds noise. Slowing the fan does the same job and cuts the power it draws.

Two relationships do the work:

Because airflow follows speed and speed follows the sheave ratio, the new motor sheave is simply the old one multiplied by design CFM over measured CFM.

Worked Example

A rooftop unit has a 1,750 RPM motor with a 4.0-inch sheave and a 9.0-inch fan sheave. A duct traverse measures 4,200 CFM against a design of 5,000 CFM. The motor is 5 HP and currently draws 2.6 brake horsepower.

The nearest stock sheave is chosen, the belt length is checked, and the system is re-measured. The fan laws predict the result well when the duct system is unchanged, but they are a prediction. The traverse after the change is what goes in the report.

What Limits a Speed Increase

Embed this calculator on your siteFree for contractors, schools, and engineering firms. Copy one snippet; it resizes itself.+
Preview the embed

Please keep the credit line under the calculator. The tool runs entirely in your visitors' browsers; nothing they enter is sent anywhere.

Frequently Asked Questions

How do I calculate fan RPM from pulley sizes?+
Fan RPM = Motor RPM × motor sheave pitch diameter ÷ fan sheave pitch diameter. A 1,750 RPM motor with a 4-inch sheave driving a 9-inch fan sheave turns the fan at 1,750 × 4 ÷ 9 = about 778 RPM. A larger motor sheave or a smaller fan sheave speeds the fan up.
Should I change the motor sheave or the fan sheave?+
Either gives the same fan speed. The motor sheave is usually smaller, cheaper, and often adjustable, so it is the one most commonly changed. Whichever is changed, check that the new size stays above the minimum sheave diameter for the belt section and motor, that the sheaves still align, and that the belt length still fits within the motor base adjustment.
What is the difference between pitch diameter and outside diameter?+
Pitch diameter is the effective diameter at which the belt rides in the groove, and it is the value that sets the speed ratio. It is slightly smaller than the outside diameter of the sheave, by an amount that depends on the belt section. Using outside diameters for both sheaves gives an approximate answer. Sheave catalogs list pitch diameter for each belt type.
How much more horsepower does a faster fan need?+
Brake horsepower rises with the cube of the speed ratio. A 10% speed increase needs 1.1³ = 1.33 times the power, a 33% increase. A 20% speed increase needs 73% more. This is why a modest airflow correction can overload a motor that had little margin, and why amps are measured after every speed change.
How do adjustable sheaves change fan speed?+
A variable-pitch sheave has a movable flange. Closing the flanges makes the belt ride higher in the groove, which increases the pitch diameter. On a motor sheave that speeds the fan up. Opening the flanges slows it down. Adjustment is made in half-turn or full-turn steps with the belt slack, and the belt is re-tensioned and realigned afterward.
Does this apply to fans with a VFD?+
The speed, pressure, and power relationships are the same. With a variable frequency drive the speed change is made by changing the drive frequency instead of the sheaves: required frequency = current frequency × design CFM ÷ measured CFM. The motor load check still applies.

Related Tools & Topics