ABS

Duct Traverse Point Planner

Generate the correct velocity measurement point positions for a round duct traverse using the Equal Area Method — the field procedure TAB technicians use to get an accurate average velocity reading instead of a single, misleading center-point measurement.

📝 Educational reference

This tool computes point positions from the Equal Area Method's underlying geometry. It is a field-planning reference, not a substitute for the specific traverse procedure and minimum point count required by your governing TAB standard or project specification.

Duct Traverse Point Planner — Equal Area Method

Why a Single Reading Isn't Enough

Air velocity across a duct's cross-section is never uniform. Friction against the duct wall slows air near the perimeter; the highest velocity sits nearer the center. A velocity probe held at the center of a duct reads the peak of that profile, not the average — using it directly to calculate CFM (velocity × area) systematically overstates actual airflow, sometimes significantly.

A traverse solves this by sampling velocity at multiple points chosen to represent equal shares of the duct's total area, then averaging the readings. That average is a much closer estimate of true average velocity across the whole cross-section.

How the Equal Area Method Works

Picture the duct's circular cross-section divided into concentric rings — like a target — where every ring has exactly the same area, even though the outer rings are thinner (since area grows with the square of radius). If you measured at the center of each ring's width, the readings wouldn't be evenly weighted by area, because the ring boundaries aren't evenly spaced.

Instead, the Equal Area Method places each measurement point at the specific radius that splits its own ring into two smaller rings of equal area. That point, mathematically: r_k = R × √((2k−1) / 2N), where R is the duct radius, N is the number of rings (points per radius), and k is the ring number counting outward from the center. Because every point now represents an equal share of total cross-sectional area, a plain arithmetic average of the velocity readings is a valid estimate of the area-weighted average velocity — no separate weighting calculation needed in the field.

Field Procedure

  1. Mark the calculated distances on a traverse rod or probe extension, measured from one duct wall.
  2. Drill or use an existing traverse port at the correct location — ideally at least 7.5 duct diameters downstream and 3 diameters upstream of any elbow, transition, or damper, per standard practice, to measure in reasonably developed flow.
  3. Insert the probe to each marked distance in turn and record the velocity reading (typically with a pitot tube and manometer, or a thermal/vane anemometer).
  4. Repeat the full set of readings along a second port, on a diameter line perpendicular to the first.
  5. Average all readings to get average velocity; multiply by the duct's cross-sectional area to get CFM.

Common Mistakes

Using too few points in a large duct: fewer points means each one represents a larger area, magnifying the effect of local turbulence or measurement error on the average.

Traversing too close to a fitting: disturbed, non-developed flow near an elbow or damper produces a velocity profile the Equal Area Method's assumptions don't hold up well against — relocate the traverse port if at all possible.

Traversing along only one diameter: skips the averaging benefit of a second, perpendicular line and is more sensitive to any asymmetry in the flow.

Embed this calculator on your siteFree for contractors, schools, and engineering firms. Copy one snippet; it resizes itself.+
Preview the embed

Please keep the credit line under the calculator. The tool runs entirely in your visitors' browsers; nothing they enter is sent anywhere.

Frequently Asked Questions

What is a duct traverse and why is it necessary?+
A duct traverse is a series of velocity measurements taken at multiple points across a duct's cross-section, then averaged, to determine average velocity and total CFM. It's necessary because velocity is not uniform across a duct — it's highest near the center and lowest near the walls due to friction — so a single center-point reading overstates average velocity and therefore overstates CFM.
What is the Equal Area Method specifically?+
The Equal Area Method divides the duct's circular cross-section into concentric rings of equal area, then measures velocity at the radius that bisects each ring into two equal-area halves. Because each point represents an equal share of the total cross-sectional area, a simple arithmetic average of the readings is a statistically valid estimate of the area-weighted average velocity.
How many traverse points should I use?+
More points improve accuracy, especially in larger ducts or turbulent flow conditions, at the cost of more field time. This tool offers 3, 5, or 10 points per radius (6, 10, or 20 points per full diameter). Your governing TAB standard (NEBB or AABC) and project specification may set a minimum point count for certified test results — confirm before relying on point counts for compliance documentation.
Do I traverse along more than one diameter?+
Yes. Standard practice measures along two diameters perpendicular to each other (90° apart) to average out any asymmetry in the velocity profile — from a nearby elbow or transition, for example. Use the same set of point positions on both lines.
Does this method work for rectangular ducts?+
This calculator's equal-area radius formula applies specifically to round ducts. Rectangular duct traverses commonly use a different approach — dividing the cross-section into a grid of equal-area rectangles and measuring at each cell's centroid — which follows the same equal-area principle but a different geometric layout.

Related Tools & Topics