ABS

9 min read · Updated

Air Balancing Equipment and Tools

Air balancing is measurement work. A technician cannot adjust what has not been measured, and the choice of instrument decides how far a reading can be trusted. This guide covers the equipment found in a test and balance kit, what each instrument measures, where it works well, and where it gives misleading numbers.

📝 Educational scope

This guide explains instrument types and their uses. It does not recommend brands or models, and ABS does not sell equipment.

The Kit at a Glance

Instrument Used for Reads Main limitation
Capture hood (balometer) Airflow at diffusers, grilles, registers Direct CFM reading Hood must fit the terminal; back-pressure compensation needed
Pitot tube + manometer Velocity in ducts, by traverse Velocity pressure, in. w.g. Unreliable below about 600 FPM; needs straight duct
Thermal (hot-wire) anemometer Low velocities: fume hoods, clean benches, low-flow ducts FPM, down to tens of FPM Fragile sensor; sensitive to probe direction and dirt
Rotating vane anemometer Face velocity at grilles, coils, filters, hoods FPM averaged over the vane Needs the right area factor to give CFM
Velocity grid Average face velocity across filters and coils FPM averaged over many points Used with a manometer; large flat faces only
Manometer + static tip Static pressure in ducts and across components in. w.g. Tip must face into the airflow
Tachometer Fan and motor shaft speed RPM Optical types need a reflective mark and line of sight
Clamp-on ammeter / multimeter Motor amps and volts A, V True-RMS meter needed on VFD-driven motors
Thermometer / hygrometer Air temperatures, humidity, coil performance °F, % RH Allow time to stabilize
Hydronic differential pressure meter Water flow at balancing valves ft of head or psi, converted to GPM Needs the valve's flow chart or Cv

Capture Hood

The capture hood, also called a flow hood or balometer, is the instrument most people picture when they think of air balancing. A fabric skirt on a lightweight frame is pressed against the ceiling around a diffuser. All of the air leaving the diffuser is funneled through a sensing grid in the base, and the meter displays airflow directly in CFM.

Its strength is speed and repeatability at terminals. A technician can read dozens of diffusers an hour without knowing anything about each one's free area. Hoods come with interchangeable frames, commonly 2 × 2 ft, 2 × 4 ft, and 1 × 4 ft, to fit different terminals.

Its weaknesses are worth knowing:

Pitot Tube and Manometer

A pitot tube is a double-walled stainless steel tube bent at a right angle. The opening at the tip faces the airflow and senses total pressure. Small holes around the outer wall sense static pressure. Connected to the two ports of a manometer, the pair gives velocity pressure, which converts to velocity through V = 4005 × √VP for standard air.

Because velocity varies across a duct, readings are taken on a grid and averaged, a procedure covered in How to Do a Pitot Tube Traverse. Done in a straight run of duct, it is the reference method for fan totals, outside air quantities, and main branch flows.

The limit is at the low end. Velocity pressure falls with the square of velocity: 0.0625 in. w.g. at 1,000 FPM, but only 0.01 in. w.g. at 400 FPM. Below roughly 600 FPM the signal is too small to read with confidence, and another instrument takes over.

The manometer itself has changed more than the tube. Inclined liquid gauges have largely given way to digital micromanometers that resolve a thousandth of an inch of water or better, store traverse readings, and apply density correction. The same instrument reads static pressure with a static tip, and differential pressure across filters, coils, and rooms.

Anemometers

An anemometer measures air velocity at a point or over a small area.

Thermal anemometers infer velocity from how quickly moving air cools a heated sensor. They read reliably down to very low velocities, which makes them the instrument for fume hood face velocity, clean bench and cleanroom velocities, and ducts moving too slowly for a pitot tube. The sensor is small and directional, and it drifts when dirty.

Rotating vane anemometers count the turns of a small propeller. The larger vane heads, around four inches, average the velocity over their own area and suit grille faces, coil faces, and kitchen hood filters. Converting a vane reading to CFM at a grille needs the grille's effective area, its Ak factor, from the manufacturer.

Velocity grids are a square array of sensing points on a handle, read through a manometer. One placement gives the average over about a square foot, which makes filter banks and large coil faces quick to survey.

Fan and Motor Instruments

Airflow is only half of a fan data sheet. The other half is what the machine is doing.

These two instruments are what make fan speed changes safe. The Fan Sheave Calculator predicts the load after a speed change, and the ammeter confirms it.

Temperature and Humidity

Digital thermometers and hygrometers record supply, return, mixed, and outside air conditions. Besides documenting coil performance, temperatures offer a second way to find the outside air fraction when a traverse of the outside air duct is not possible: the mixed air temperature sits between the return and outside temperatures in proportion to the two airflows.

Hydronic Instruments

Testing, adjusting, and balancing covers water as well as air. Flow through a coil is set at a calibrated balancing valve. A differential pressure meter connects to the valve's two test ports, and the pressure drop is converted to gallons per minute using the valve manufacturer's chart for that size and setting. Where no measuring device is installed, an ultrasonic flow meter clamped to the outside of the pipe can measure flow without cutting in.

The Small Things

A working kit also holds the items that make measurement possible: a drill and step bit for traverse holes, plugs to seal them afterward, static pressure tips, tubing, a smoke source for showing air direction at doors and hoods, a tape measure for duct dimensions, and a ladder tall enough to hold a hood square against the ceiling.

Calibration

An instrument's reading is only evidence if the instrument is known to be accurate. NEBB, AABC, and TABB all require their certified firms to own a defined set of instruments and to calibrate them on a schedule, typically annually for the principal airflow and pressure instruments, against standards traceable to a national laboratory. The calibration date of each instrument is listed in the balance report. When reviewing a report, that list is one of the first things to check, as described in How to Read an Air Balance Report.

FAQ

What equipment is needed for air balancing?+
At minimum: a capture hood for measuring airflow at diffusers and grilles, a digital manometer with a pitot tube and static pressure tips for duct measurements, an anemometer for face velocities, a tachometer for fan speed, a clamp-on ammeter for motor load, and a thermometer or hygrometer. Hydronic balancing adds a differential pressure meter for balancing valves.
What is the most accurate way to measure airflow?+
A pitot tube traverse in a long, straight section of duct is generally treated as the reference method for total airflow, because it measures velocity directly across the whole cross-section. A capture hood is the most accurate practical method at individual terminals. Each is only as good as the conditions it is used in: a traverse close to an elbow or a hood on a diffuser it was not designed for will both mislead.
What is a balometer?+
A balometer is another name for an airflow capture hood. It is a fabric hood on a frame that is held over a diffuser or grille so that all the air passes through a measuring grid at its base, giving a direct reading in CFM. The word began as a product name and is now used generically.
How often do balancing instruments need calibration?+
Certifying bodies set calibration intervals for each instrument type, and twelve months is typical for the main airflow and pressure instruments. A TAB report lists each instrument with its serial number and calibration date so the reader can confirm it was in calibration on the day of testing.
Can a vane anemometer replace a capture hood?+
Only with care. An anemometer gives velocity at the points where it is held. Turning that into airflow at a grille requires an average over the face and the correct effective area, the Ak factor, for that grille. It works reasonably on plain return and exhaust grilles and poorly on supply diffusers with complex throw patterns. A hood removes both problems by capturing all of the air.
Why do capture hood readings need a correction?+
Placing a hood over a diffuser adds resistance, which slightly reduces the airflow being measured, more so on low-pressure systems and at high flows. Modern hoods compensate for this back pressure, either automatically or through a two-reading procedure with a flap open and closed. Some diffuser types also need a manufacturer or field-derived correction factor.