ABS

6 min read · Updated

Air Balancing vs. Title 24 Acceptance Testing

On a California commercial project, the balancing contractor and the acceptance test technician arrive at roughly the same time, carry some of the same instruments, and look at the same air handlers. It is easy to assume one test covers the other. It does not. They answer different questions, are required by different codes, and are signed off by people with different certifications.

📝 Educational reference

This page compares the two for planning purposes. The project specification and Certificate of Compliance govern what a specific project requires.

Side by Side

Air balancing (TAB) Title 24 acceptance testing
Purpose Set airflow and water flow to design at every fan and terminal Confirm specific energy-related functions work as the Energy Code requires
Required by Project specifications; CALGreen for new nonresidential systems California Energy Code, Section 120.5
Performed by Firm certified by NEBB, AABC, or TABB, as specified Certified Mechanical Acceptance Test Technician
Output Balance report with design vs. measured values Certificate of Acceptance (NRCA-MCH) per test
Scope Every outlet, fan, and coil Selected functions: outdoor air, economizer, DCV, variable flow, resets, FDD
Result Values within tolerance, with a deficiency list Pass or fail for each test

Where They Overlap

Outdoor air. The outdoor air acceptance test (NRCA-MCH-02-A) measures the outdoor airflow the system brings in and compares it with the design minimum. Setting that minimum is a balancing task. If balancing has not established and marked the minimum damper position, the acceptance test has nothing to verify.

Variable air volume systems. The supply fan variable flow test (NRCA-MCH-07-A) relies on calibrated terminal units and a duct static pressure setpoint, and both are established during balancing.

Duct leakage. On qualifying single-zone nonresidential systems, duct leakage is an acceptance test (NRCA-MCH-04-A). A balancer sees the same problem from the other side, as a gap between fan airflow and the sum of the outlets. See Air Balancing vs. Air Tightness Testing.

Where They Do Not

Most acceptance tests check controls, not airflow: that an economizer's high limit locks it out, that a CO₂ sensor drives the outdoor air damper, that water temperatures reset, that fault detection reports a simulated fault. Balancing does not test any of that. In the other direction, acceptance testing does not touch most terminals. A building can pass every acceptance test with half its diffusers out of balance.

And ECC Verification?

In homes there is no acceptance testing. The equivalent checks, such as duct leakage, airflow, fan efficacy, and refrigerant charge, are field verifications by an ECC-Rater, described in HERS to ECC. Residential air balancing in the TAB sense is not a code requirement, though the airflow verification covers part of the same ground.

Scheduling Them

  1. Duct leakage testing during installation, where specified
  2. Equipment start-up and controls programming
  3. Testing, adjusting, and balancing
  4. Title 24 acceptance tests
  5. Commissioning functional testing, where required
  6. Final inspection

Combining steps 3 and 4 in one visit, with one firm holding both certifications, is the efficient version of this sequence and avoids the most common cause of failed acceptance tests: testing a system that is not yet ready.

FAQ

Is air balancing required by Title 24?+
Not by the Energy Code's acceptance test list. Balancing is required through other channels: CALGreen, Part 11 of Title 24, includes testing and balancing requirements for new nonresidential HVAC systems, and project specifications almost always require it. In practice, the Energy Code's outdoor air acceptance test cannot pass on a system that has not been balanced.
Can the same firm do air balancing and acceptance testing?+
Yes, if its technicians hold the right certifications. Balancing on commercial projects is normally done by a firm certified by NEBB, AABC, or TABB, while acceptance tests require individuals certified as Mechanical Acceptance Test Technicians. A firm with both can balance a system and then run the acceptance tests in one mobilization.
Which comes first?+
Balancing. Acceptance tests check functions such as outdoor airflow and economizer operation, and those depend on the airflows and damper positions that balancing sets. Testing before balancing is finished is a common reason for failed tests and return visits.
Does an air balance report count as an acceptance test?+
No. A balance report documents airflow at every terminal and fan. An acceptance test is a specific pass or fail test recorded on a Certificate of Acceptance through a certification provider. The balance report can support the outdoor air test, but it cannot replace the form.